ABOUT

Solutions & Cases

Our Case
  • EFFECT OF SUPERPLASTICIZER ON PROPERTIES OF MORTAR

    was that for mortar containing the superplasticizer additive at 00C compared with reference mortar mix. For reference mortar mix M1 at (28) days, the residual compressive strengths are about (41 N/mm 2, 40 N/mm) at a temperature of (200, 400)0C respectively. The residual stresses for mortar containing additives are about (33 N/mm2, 32

  • (PDF) EFFECT OF SUPERPLASTICIZER ON PROPERTIES OF MORTAR

    Twenty concrete mixes were prepared, keeping the water/cement ratio constant at w/c = 0.40, with different amounts of SP admixture, and NS. the superplasticizer was studied in the range of (0

  • PAPER OPEN ACCESS Optimization of superplasticizer in

    the flow behavior of PPC mortar and to find the saturation dosage of superplasticizer in cement mortar of cement to sand proportion 1:1.5. Main parameters which affect the concrete flow behavior are paste rheology, aggregate volume fraction and aggregate particle size distribution. So Influence of aggregates and the aggregate-paste

  • Superplasticizers Cemkem

    Manufactured in the UK, Cemkem’s range of powder superplasticizers for mortar and concrete have three functionalities: 1. To create flowing, self-levelling properties without increasing water demand, without need to cement content, without compromising strengths. 2. To produce workable, high-strength concrete and mortar through reduction in

  • Superplasticizer Wikipedia

    Superplasticizers (SP's), also known as high range water reducers, are additives used in making high strength concrete. Plasticizers are chemical compounds that enable the production of concrete with approximately 15% less water content. Superplasticizers allow reduction in water content by 30% or more. These additives are employed at the level of a few weight percent.

  • Influence of the HLB value of polycarboxylate

    Jun 01, 2014· Applicators of mortars and concretes admixed with polycarboxylate superplasticizers routinely observe that at low water-to-cement (w/c) ratios (e.g. < 0.40), the mortar or concrete can attain a sticky, viscous consistency and honey-like, creeping flow behavior which is highly undesirable for pumping, placement and compaction of such concrete.

  • (PDF) Dosage Limit Determination of Superplasticizing

    An admixture, according to the ASTM C-125-97a standards, is a material other than water, aggregates or hydraulic cement that is used as an ingredient of concrete or mortar, and is added to the

  • A Contractor’s Guide to Superplasticizers

    Superplasticized concrete pumps easily and arr i v e s workable. For maximum effectiveness, however, superplasticizers must be added to the mix at the right time. THE USE OF A TYPE G ADMIXTURE MAY REQUIRE A FINISHING CREW TO WAIT THREE ADDITIONAL HOURS BECAUSE THE ADMIXTURE RETARDS THE SET.

  • Use of Water Reducers, Retarders, and Superplasticizer

    Water reducers, retarders, and superplasticizers are admixtures for concrete, which are added in order to reduce the water content in a mixture or to slow the setting rate of the concrete while retaining the flowing properties of a concrete mixture. Admixtures are used to modify the properties of concrete or mortar to make them more suitable to

  • Chemical Admixtures

    Superplasticizers, also known as plasticizers or high-range water reducers (HRWR), reduce water content by 12 to 30 percent and can be added to concrete with a low-to-normal slump and water-cement ratio to make high-slump flowing concrete. Flowing concrete is a highly fluid but workable concrete that can be placed with little or no vibration or

  • EFFECT OF SUPERPLASTICIZER ON PROPERTIES OF MORTAR

    was that for mortar containing the superplasticizer additive at 00C compared with reference mortar mix. For reference mortar mix M1 at (28) days, the residual compressive strengths are about (41 N/mm 2, 40 N/mm) at a temperature of (200, 400)0C respectively. The residual stresses for mortar containing additives are about (33 N/mm2, 32

  • (PDF) EFFECT OF SUPERPLASTICIZER ON PROPERTIES OF MORTAR

    Twenty concrete mixes were prepared, keeping the water/cement ratio constant at w/c = 0.40, with different amounts of SP admixture, and NS. the superplasticizer was studied in the range of (0

  • Super plasticizer I Water reducer I GlobMarble concrete

    How to Mix Directions: How to mix with Cementitious Material: Mix pre-mixed concrete or cement with plasticizer for a few minutes, then add water (mix at least 3-5 minutes). You can also add Super plasticizer to the water 10-15 minutes prior to casting (until

  • apeg for polycarboxylate superplasticizer, apeg for

    apeg for polycarboxylate superplasticizer, Wholesale Various High Quality apeg for polycarboxylate superplasticizer Products from Global Sodium Tripolyphosphate Suppliers and apeg for polycarboxylate superplasticizer Factory,Importer,Exporter at Okchem.

  • Super Plasticizers: Classification and Uses Concrete

    2. For the same workability, the use of super plasticizer permits the use of lower water/cement ratio. 3. The use of super plasticizer also permits the reduction in cement content due to the increase in strength. 4. The use of plasticizers also produces a homogeneous and cohesive concrete without any tendency of segregation and bleeding.

  • Influence of the HLB value of polycarboxylate

    Jun 01, 2014· Applicators of mortars and concretes admixed with polycarboxylate superplasticizers routinely observe that at low water-to-cement (w/c) ratios (e.g. < 0.40), the mortar or concrete can attain a sticky, viscous consistency and honey-like, creeping flow behavior which is highly undesirable for pumping, placement and compaction of such concrete.

  • Superplasticizer an overview ScienceDirect Topics

    R. Flatt, I. Schober, in Understanding the Rheology of Concrete, 2012. 7.2.3 Formulations. When a concrete producer buys a superplasticizer, it seldom consists of just a pure solution of one of the previously described superplasticizer polymers.Commercial superplasticizers are usually formulated products adapted for the special needs of the respective market, application or area.

  • (PDF) Dosage Limit Determination of Superplasticizing

    An admixture, according to the ASTM C-125-97a standards, is a material other than water, aggregates or hydraulic cement that is used as an ingredient of concrete or mortar, and is added to the

  • Cement Superplasticizer Compatibility The Concrete Portal

    Cement superplasticizer interaction in concrete is a complex blend of chemical and physical mechanisms that are interdependent. The complicated nature of the problem prevents the development of simple solutions to address the field related issues of application of superplasticizers.

  • A Contractor’s Guide to Superplasticizers

    Superplasticized concrete pumps easily and arr i v e s workable. For maximum effectiveness, however, superplasticizers must be added to the mix at the right time. THE USE OF A TYPE G ADMIXTURE MAY REQUIRE A FINISHING CREW TO WAIT THREE ADDITIONAL HOURS BECAUSE THE ADMIXTURE RETARDS THE SET.